You’ll need to do this later anyway to make a few changes to your router’s settings. There are many ways to do this, one of the easiest is by logging into your routers admin page. To do this, you first need to figure out your Pi’s IP address, which has been assigned by your router. Now that you’ve got your Pi booted up and (hopefully) running, you need to be able to access it in order to install Pi-hole onto it and make any settings changes or updates. First Boot & Connecting To Your Pi Zero W Finding Your Pi’s IP Address Plug the SD card into your Pi, then put it into it’s case and plug the power cable in. Once you’ve got both of these files then you can eject and remove your SD card. ![]() So the file should just be a blank file called ssh with no extension. Thats the first done, now we need to add an SSH file.Ĭreate a new text file and change its name to ssh and remove the extension. Now copy this file into your boot directory. Now change the extension of the file from. You can also change your country code at the top if you’d like, this can be set up later though. In the network settings section, you need to add your local WiFi network name next to ssid and your network password next to psk, leaving all of the punctuation marks in place. We need to add two files to this directory, one to tell the Pi how to connect to your network and another to enable SSH so that you can access it over the network.ĭownload the network settings template wpa_supplicant and open it using a basic text editor like Wordpad. The will be one readable partition on the card called boot, you should be able to open this partition and you’ll see a number of files. You might get a couple of windows pop up and one which says you need to format the card in order to use it, just ignore these and close them. There is a bit more to do on the SD card before we’re done on the computer, so you’ll need to plug it in again to access it. Click write and let the tool do the rest, it’ll write the image, check it and then eject the SD card. You just select the Raspberry Pi operating system you need, which in our case is Raspberry Pi OS Lite, and then select the SD card you want to write the image to. They have a version for Windows, Mac and Linux. This is a fairly new tool and it’s one of the easiest to use. Start by downloading the Raspberry Pi Imager on your computer. Don’t worry about formatting it just yet, we’ll get to that in a minute. ![]() Plug your microSD card into your computer. We’ll start by preparing the Raspberry Pi’s operating system on the SD card, Pi-hole will then be installed to run on this operating system later. Preparing Raspberry Pi OS Lite On The SD Card You won’t need a mouse, keyboard or monitor for this as we’ll be using another computer on the network to set up the Pi-hole. You can usually buy these kits online for around $30-$50 dollars which includes everything you need, even a power supply, although you can buy the Pi alone for as little as $10 if you do some searching. You’re going to need a Raspberry Pi Zero W, a micro SD card of at least 16GB, and something to put the Pi into to protect it, I just used the official case. Raspberry Pi Zero W Complete Kit – Buy HereĪlternately, buy the individual components:.What You Need To Make Your Own Pi-hole Ad Blocker Here’s a step by step video guide to setting up your Pi-hole, read on for the written guide: But for a smaller home network with less than 50 devices and only a couple of users online at a time, a Pi Zero W works perfectly. If you’re running a large network with lots of users and traffic then the best device to use would be one of the Raspberry Pi 3 or 4 models with an ethernet connection to your router. ![]() Now that you know what Pi-hole is, let’s have a look at how to to set one up on your home network, step by step. This also saves data if you’re on a limited data plan.Ī web interface lets you interact with your Pi-hole and view stats on your network traffic. Pi-hole also improves your network speed, because the ads are blocked before they are downloaded. It enables you to block ads on websites, ads in apps on your mobile devices and even on your smart TV, regardless of the software they’re running and without the need for any other local software on the device. ![]() Pi-hole is a clever piece of software which acts as a network-wide ad blocker.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |